OWNER/OPERATOR MANUALBRUSHCUTTERST3108-93110(108) The engine exhaust from this productcontains chemicals known to the Stateof California to cause canc
10 Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting at
• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap
12 5. For safe operationrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks, or any
MOUNTING ENGINE (SE1)1. Loosen the bolts temporarily attached to theclutch housing.2. Push the driveshaft toward the gearcase androtate it by hand t
14 6. Set up INSTALLING CUTTING HEAD (SE6)1. While locking the gear shaft by inserting theattached bar into the upper holder and the gearbox, loose
• Gasoline is very flammable. Avoid smokingor bringing any flame or sparks near fuel.Make sure to stop the engine and allow itcool before refueling t
16 at least one minute.5. Put a clear indication on the outside of thecontainer to avoid mixing up with gasoline orother containers.6. Indicate the
STARTING ENGINE1. Rest the unit on a flat, firm place. Keep thecutting head off the ground and clear ofsurrounding objects as it will start rotating
18 8. Operation STOPPING ENGINE1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP position.
3. You can avoid thrown debris by sweeping fromyour left to the right.4. Use a slow, deliberate action to cut heavygrowth. The rate of cutting motion
20 9. Maintenance• Always be sure to stop the engine beforeinspecting the brushcutter for problems orperforming maintenance.• Never alter the brushc
• Make sure that the engine has stopped and iscool before performing any service to thebrushcutter. Contact with moving cuttinghead or hot muffler may
22 MUFFLER• Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If anysign of exhaust leakage is found, do not usethe b
9. Maintenancebecome overheated, and that this in turncould cause the brushcutter to catch on fire.Always make sure that the muffler is cleanand free
24 10. Storage• Aged fuel is one of major causes of enginestarting failure. Before storing the unit, empty thefuel tank and run the engine until it
Under growthHeavy weedsLight weedsGrassNylon line headCUTTER APPLICATIONCHART9” 22-tooth:SST2299” 24-tooth:SST2498” 8-tooth:SGB0889” 8-tooth:SGB0898”
26 11. Optional blade usage• When sharpening, removing, or reattachingthe blade, be sure to wear thick, sturdygloves and use only proper tools andeq
11. Optional blade usage CUTTING METHODa) Use the front left side cutting.b) Guide the blade from your right to left with ittilted slightly to your l
By using the shoulder strap, hang the unit onyour right side. Adjust the strap length so thatthe cutting head may become parallel to theground. (OPT
11. Optional blade usage29 OPT11the blade is fed faster than its cuttingcapability.f. Cut only from your right to your left.g. Keep your path of adv
SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to
30 12. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel fil
13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr
13. Parts list 32 Fig.1 DRIVE UNIT BC225DL (S/N 120000 and up)
Key# Description Part Number Q'tyFig.1 DRIVE UNIT BC225DL (S/N 120000 and up)Key# Description Part Number Q'ty1 PIPE COMP T3108-12100 12 SH
Fig.2 ENGINE UNIT BC225DL (S/N 000101 and up)34 13. Parts list
Key# Description Part Number Q'tyFig.2 ENGINE UNIT BC225DL (S/N 000101 and up)35 Key# Description Part Number Q'ty1 CYLINDER 5580-12110 1
The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL BC225DL UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), TH
Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur
2. Specifications BC225DLOverall size(LxWxH)······················································ 70.8(1800)x12.8(325)x13.0(330) in(mm)Dry weight w/
KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093 © Printed in Japan
(1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4) Keep all children, bystander
6 For safe operation and maintenance,symbols are carved in relief on the machine.According to these indications, please becareful not to make a mist
7 5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this ma
8 b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview o
BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area into w
Komentáře k této Příručce